
- #Cloning mac ip for comcast modem free internet how to
- #Cloning mac ip for comcast modem free internet free
- #Cloning mac ip for comcast modem free internet windows
By default DHCP remembers the last address it got, even if you do a DHCP /release.
#Cloning mac ip for comcast modem free internet windows
I suspect where the poster was going with that recommendation was to try and get Windows to forget about its previous address assignments. If proper end-station configuration was an absolute requirement to ensure the health of the overall network, we would be completely screwed. your network card has a unique id (MAC Address) that your ISP has tied to each ip address you use with their service.Īssigning yourself an RFC1918 address isn't going to cause network problems, it's just going to hose up your ability to interface with the network. Remember, this doesn't protect you from being tracked by those that have the resources to do so. Poof! your ip address has changed and you can log back on to that banned game room (or whatever).
#Cloning mac ip for comcast modem free internet free
after you've verified that the address has been changed (double click on your local area connection icon and look at the support tab), feel free to close the network connections folder. this time, select "obtain ip address automatically". from here, start again, getting back to tcp/ip properties (don't remember? follow the steps above). this will put you back into the network connections folder. if not, do so.Ĭlick okay, then okay again on the aforementioned local areas connections properties. below that is the gateway and by default, if you hit TAB, it will fill with 255.0.0.0. In the ip address field, use a "undefined" (and thus, unused) ip address (such as 10.1.1.1) by mouse-clicking into each field and entering the corresponding number. Under the "general" tab, select the radio button that says "use the following ip address" you'll be back here in less than a minute so remember where it is.) (you should be at tcp/ip properties at this point.
image003.png)
Go to the properties of the local area connection (again, right click, properties)ĭouble-click on internet protocol tcp/ip. Go to your tcp/ip properties (right click on my network places, select 'properties' from the list) Ipconfig /release (then enter, of course)
#Cloning mac ip for comcast modem free internet how to
(if you can't figure out how to do that, you probably shouldn't do this.)įirst, at the command prompt, (start, run, command) type:

Take note of your ip address beforehand to verify your changes. To change your dynamic IP address (like those with attbi and comcast) in Windows XP (in less than 60 seconds without additional software): maybe you didn't read my post entirely? or maybe i didn't make my post clear enough. Well like i said, it works for me.changes my ip everytime i do that. # Enter ? for additional hints on searching ARIN's WHOIS database.Riiight.Īnd selecting DHCP afterwards, will give you the same one you had before. OrgTechEmail: ARIN WHOIS database, last updated 19:10 OrgTechName: Internet Corporation for Assigned Names and Number OrgAbuseName: Internet Corporation for Assigned Names and Number I appreciate any help.OrgName: Internet Assigned Numbers AuthorityĬomment: This block is reserved for special purposes.Ĭomment: Please see RFC 1918 for additional information. All I know and please correct me if I am wrong that the MAC address of the router is the original address registered with the ISP and the local MAC address is the new address now assigned. I don't know if they are suppose to match. So I am wondering if something is in conflict and I then noticed the local MAC address and that is it different from my MAC address. I noticed that my router was no longer in an error state and my computer says I have internet connection.but I still cannot connect to the net. And then reboot the router and the modem. I then enabled MAC clone and cloned back my original MAC address (I noticed it had changed under status of the router). I then found this site and followed with the notions of rebooting the router. I at first called my ISP and he said that my router has been refusing their packets.

I am not that computer literate and of course frustrated at this point. And I followed what was mentioned here, but I am still kind of stuck.

I did the same thing with renewing and releasing the DHCP and nothing happens. I have though a WRV54G router (firmware version 2.39.2). Sorry for bringing this topic back, but I am actually suffering from the same problem as the original poster did.
